Understanding Essential Plumbing Skills is Essential for Installing a Bathtub
Understanding Essential Plumbing Skills is Essential for Installing a Bathtub
Blog Article
Just about every person will have his or her own perception when it comes to Installing A Bathtub.
Mounting a bathtub isn't exactly brain surgery, however it does call for strong plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately tough job. If the old bathtub is readily easily accessible, the project can relocate immediately; if you have to open a wall surface to eliminate the old tub as well as place the brand-new bathtub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly require an assistant to leave the old tub and set in the brand-new one. Make sure you have actually qualified yourself for the work as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed task, it is far better to consider employing one prior to you begin. Chances are you may need a professional plumber to make tube links.
This short article will aid you install a brand-new tub in your restroom if you have already purchased a new bathtub as well as don't need to transform the plan of your previous water system pipelines.
Your tools and also material list ought to make up the following:
Preparing for the Installation
Firstly, the sustaining framework provided with the bath should be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to avoid stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be suited its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be quite troublesome due to the restricted access that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a cloth ready for the remaining water that will originate from the pipes. Once the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. Once the taps have been removed, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Before going on to fit the brand-new taps, contrast the pipeline links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of the two wood boards under its feet, position the tub in the called for position. The wood boards are valuable in uniformly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the tub up until the level reviews degree.
To install taps, fit the bottom of the furthest versatile faucet adapter to the proper supply pipe by making a compression join; then do the same for the other tap.
Activate the water and check all joints and new pipework for leaks as well as tighten them if essential. Fill the bath tub and also check the overflow electrical outlet as well as the typical electrical outlet for leakages.
Finally, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the tub should wait until the bath tub has actually been made use of a minimum of once as this will settle it right into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washers are in location between the faucet and also the sink. Secure the faucet in position with the manufacturer supplied backnut. Once the tap is securely in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap ports. The former kind needs to be linked to the tap ends initially, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to split an inflexible seal, triggering the water to permeate the wall surface between the bath and also the tiling, resulting in problems with moisture and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes as well as cartridges, and also are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of soaked paper or soft rope. Remember to always fill up the bathtub with water before sealing, to allow for the movement experienced when the tub remains in use. The sealant can fracture fairly very early if you do not take into consideration this motion prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly readily available on the market. It is a good idea to fit the tiles making use of water-resistant or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very intrigued by Tools You Need to Install a New Bathtub and I hope you liked my entry. Make sure you take a moment to distribute this entry if you appreciated it. Many thanks for going through it.
Drips? Dial fast! Report this page